Gas fireplace service
Sweep & inspection
Caps & crowns
Flue relining
Masonry repairLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Why Bustleton Homeowners Choose DuraFlex Chimney Cleaning
We provide independent DuraFlex chimney cleaning service in Bustleton, PA. That means we clean, inspect and repair flues lined with a DuraFlex flexible stainless steel chimney liner, and we tell you plainly what condition the liner is in before anything gets recommended. Bustleton’s older masonry chimneys and offset flues wear a DuraFlex liner in particular ways, and knowing those wear points is the whole job.
DuraFlex is a flexible stainless steel chimney liner, and it’s one of the most common relining systems in this part of Philadelphia. We’re an independent DuraFlex service provider. We are not affiliated with, authorized by or certified by DuraFlex, and we don’t present ourselves as a dealer. What we bring is familiarity: the technicians we connect you with have pulled, inspected and re-terminated enough of these liners to recognize their telltale wear points on sight. Our technicians have up to 9 years of experience.
We handle the full system, not just the sweep: annual cleaning, Level 2 inspection, cap and crown work, liner service and fireplace repair. If you’re in Bustleton and want a straight answer about your DuraFlex flue, call (833) 350-7109. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Why Trust Chimney Sweep Bustleton for Your DuraFlex Chimney Cleaning?
A DuraFlex liner isn’t a masonry flue, and treating it like one is how liners get damaged. The technicians we work with know the difference between a liner that needs a proper sweep and one that needs to be re-secured, re-sealed or, in the worst cases, replaced. That judgment comes from hands-on time with these systems, not from a manufacturer badge.
We use quality parts that fit DuraFlex equipment: top plates, caps, appliance connectors and insulation wrap matched to the installed liner’s wall type and diameter. We don’t stock or sell OEM DuraFlex parts, and we don’t claim to. What we do is specify the right component for the liner that’s actually in your chimney.
Service is warranty-safe. We clean with brushes sized to the liner diameter and avoid the practices that void coverage on flexible liners, like over-brushing a single-wall run or hauling on a top plate that’s already compromised. When we’re on a Bustleton roof, we photograph what we find so you can see the liner’s condition yourself rather than take our word for it. The local professional is licensed and insured as their state requires. From annual cleaning to full liner replacement, one call covers it.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Common DuraFlex Chimney Cleaning Problems We Fix in Bustleton
Bustleton is overwhelmingly post-war brick. Rowhouses and twins built from the late 1940s through the 1960s, most with a single masonry fireplace and an exterior brick chimney. Those chimneys are 60 to 75 years old now, and many were built with undersized flues and no modern liner, which is exactly why so many of them got relined with a flexible stainless system in the first place. The failures we see on DuraFlex runs here follow a pattern.
- Top-plate and cap seals loosening or cracking. The plate and cap at the top of the liner are the first line of defense against water. When the seal cracks, rain and debris run down the outside of the liner and into the smoke chamber. Philadelphia’s freeze-thaw winters work on that seal every year, and a failed top plate is one of the most common things we find on a Bustleton roof.
- Creosote and soot bridging on the corrugated inner wall. Single-wall DuraFlex liners have a corrugated interior, and creosote collects in those corrugations, especially where the flue offsets. A brush that’s too small skips over the ridges. A brush sized correctly to the liner diameter reaches them. This is the single biggest reason a DuraFlex flue stops drafting the way it used to.
- Liner joints and the appliance connector working loose. Years of heating and cooling cycling expand and contract the liner and its connections. Joints and the connector at the appliance can slip or work loose, which lets flue gases escape where they shouldn’t. It’s a small mechanical problem with serious consequences, and it’s easy to miss without a proper inspection.
- Insulation wrap degrading on insulated runs. Insulated DuraFlex kits rely on their wrap to hold heat and keep the outer jacket from condensing. When the wrap breaks down, draft drops and moisture collects on the outer jacket. That moisture is often mistaken for a leak from above.
- Undersized liner for the appliance. Some Bustleton flues were relined for one appliance and later had a different insert or stove connected. An undersized liner won’t draft correctly no matter how clean it is, and the fix isn’t another sweep.
A typical DuraFlex job usually goes like this: a homeowner notices a smoky smell and weak draft, and the sweep finds creosote packed into the corrugations where the liner offsets, plus a rusted-through top plate letting water in. The usual fix is a proper poly-brush sweep sized to the liner’s diameter, then replacement of the top plate and cap and a check of the appliance connector, with a Level 2 camera inspection to confirm the liner itself isn’t split or crushed. That’s how it goes in most cases. Sometimes it’s simpler. Sometimes it’s more.
A safety note. Flue work means height, and it means combustion gases. If you suspect a cracked liner, a loose connector or carbon monoxide getting into the living space, don’t wait and don’t climb up there yourself. Chimney sweeping and liner work are trained-professional territory. What you can safely do is check your carbon monoxide detector and call us.
DuraFlex Parts & Our Repair-vs-Replace Approach
We choose parts that fit DuraFlex equipment: compatible top plates, caps, appliance connectors and insulation wrap, matched to the liner’s wall type and diameter. Fit matters more than label here. A cap that’s the wrong size lets water past the plate. A connector that doesn’t seat properly is a leak waiting for the first cold snap.
Repair versus replace comes down to the liner itself. If the liner is sound, we re-secure and reseal it rather than push a full reline. A top plate and cap replacement plus a thorough sweep solves most of what we find. We only recommend replacement when the liner is crushed, split, or undersized for the appliance it’s serving. You’ll see the camera evidence and the photos before any decision, and we’ll tell you when a repair can safely wait a season.
Nothing gets recommended without evidence you can look at yourself. Call (833) 350-7109 for an exact quote. Estimates are free.
Our DuraFlex Service Process – Step by Step
- 1
Diagnosis. We start with a Level 2 inspection, which includes a camera run of the full liner. That shows corrugation creosote, offset sections where the liner ovalizes, joint condition and the appliance connector. We document the top plate and cap from the roof at the same time.
- 2
Repair or install. Depending on what the inspection shows, this is either a sweep with a poly brush sized to the liner diameter, a top plate and cap replacement, a connector re-seat, or a new DuraFlex liner install. We specify the material by name and match components to the existing liner’s wall type and diameter.
- 3
Test. After the work, we check draft at the appliance and verify the top termination is sealed. If there’s an insert or stove, we confirm the connector is tight. A flue that drafts correctly is the whole point of the work.
- 4
Warranty and records. We leave you with photos and a record of what was found and what was done. That documentation matters if a DuraFlex liner ever needs a warranty discussion, and it gives the next technician a real starting point.
See the difference
Before
After
Before
After
Before
AfterDuraFlex Products We Service & Install in Bustleton
We service and install DuraFlex flexible stainless steel liners in the configurations that show up in Bustleton’s older homes. That includes single-wall round DuraFlex SS liners in standard flues, insulated DuraFlex Pro flexible liner kits where draft and condensation control matter, and ovalized flexible liners for the offset flues so common in post-war rowhouses. We also handle liner terminations: top plates, caps and the termination kit that seals the top of the run.
Each of these wears differently, and each calls for a brush sized to it and a component matched to it. On a Bustleton flue, a single-wall run with corrugation creosote is a different job from an insulated run with a degrading wrap, and we treat it that way.
We Also Service These Brands
DuraFlex is one system among several we work with. We also clean and service flues to HeatShield standards, using HeatShield resurfacing where a masonry flue needs restoration rather than a new liner, and we install Gelco chimney caps. That range matters in Bustleton, because the right solution on your chimney depends on what’s actually in the flue, not on which brand we’d rather sell.
FAQs – DuraFlex Chimney Cleaning Service in Bustleton
No. We’re an independent DuraFlex service provider. We’re not affiliated with, authorized by or certified by DuraFlex, and we don’t claim to be. Our knowledge of these liners comes from working on them in Bustleton and across the area, not from a manufacturer program. Call (833) 350-7109 if you want an independent assessment of your flue.
Yes. We use compatible top plates, caps, appliance connectors and insulation wrap matched to the installed DuraFlex liner’s wall type and diameter. We don’t stock or sell OEM DuraFlex parts and we don’t present ourselves as a dealer. What we do is specify the right component for the liner you actually have. Call (833) 350-7109 for an exact quote. Estimates are free.
A standard sweep and inspection on a DuraFlex-lined flue usually takes a couple of hours, and a top plate and cap replacement adds time on the roof. A full liner install is a longer job, planned in advance. We’ll give you a realistic window when we book, based on what the inspection shows. Call (833) 350-7109 to schedule.
We cover the flexible stainless steel liners and their terminations: single-wall round DuraFlex SS liners, insulated flexible liner kits, ovalized liners for offset flues, and the top plate and cap termination kits that seal the run. If it’s a DuraFlex liner in a Bustleton chimney, we can inspect and clean it.
Proper service shouldn’t void your DuraFlex warranty, and we work to keep it that way. That means brushes sized to the liner diameter, no over-brushing a single-wall run, and no forcing a compromised top plate. We document what we find with photos so there’s a clear record if warranty ever comes up. Call (833) 350-7109 with questions about your liner.
Yes. A DuraFlex liner gets a poly brush sized to its inside diameter, because an oversized brush on a flexible liner can distort or damage the wall and an undersized one skips the creosote packed in the corrugations. A masonry flue takes a different brush and a different approach. Getting the brush wrong is how a clean-looking flue keeps smoking. Call (833) 350-7109 if your DuraFlex flue still drafts poorly after a sweep.
Most often it’s a failed top plate or cap seal. When the seal at the top of the liner cracks, rain runs down the outside of the liner and into the smoke chamber. A rusted-through plate is a common find on older Bustleton roofs. The fix is usually a top plate and cap replacement, not a new liner. Call (833) 350-7109 for an exact quote. Estimates are free.
Yes, but it takes the right brush. An ovalized section changes the liner’s inside dimensions, and a round brush sized to the main run won’t clean the offset properly. We size the brush to the section being cleaned and check the offset with the camera. Call (833) 350-7109 to book an inspection.
You know by looking at it. If the camera inspection shows the liner crushed, split, or undersized for the appliance, replacement is the answer. If it’s sound and the problem is creosote or a bad top plate, a cleaning and reseal is enough. We don’t recommend replacement without evidence you can see. Call (833) 350-7109 for an exact quote. Estimates are free.
For most inserts, an annual sweep plus a Level 2 inspection is the right baseline. Inserts on a DuraFlex liner can hide problems above the connector, though, where creosote bridges the corrugations and the wrap degrades. The inspection is what confirms the sweep was enough. Call (833) 350-7109 to book yours before the cold season starts.
Book Your DuraFlex Service in Bustleton, PA
If your Bustleton home has a DuraFlex liner and you want an honest read on its condition, call (833) 350-7109. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Every visit starts with an inspection and photos you can see, and the written estimate sets the final price. Estimates are free.
Written by the team at Chimney Sweep Bustleton.