Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Liner & Rebuild for Bustleton Homeowners
If your fireplace smells like smoke when it’s cold out, or a sweep has told you the clay tiles inside your flue are cracked and flaking, you’re looking at liner work or a rebuild. Those aren’t jobs for a general repair company. We handle the full system, not just the sweep: from a stainless liner for a straightforward flue to a partial or full rebuild when the masonry itself has failed. Our technicians have up to 9 years of experience, and we specify the material by name so you know exactly what’s going into your chimney. Same-day visits are often possible in Bustleton, and estimates are free. Call (833) 350-7109.
What Our Chimney Liner & Rebuild Service Includes
Replacing a liner and rebuilding a chimney are different kinds of work, and it helps to know which one your chimney actually needs before you agree to anything. Here’s how we break it down.
Stainless Steel Liner
A stainless steel liner is a rigid or semi-rigid pipe that runs the full height of the flue and gives the smoke and gases a clean path out. It’s the usual fix when the original clay tile flue has cracked, separated at the joints, or is too oversized for the appliance venting into it. We size the liner to the appliance and the chimney, then insulate around it so the flue heats evenly and draws properly.
Flexible Liner
A flexible liner is the same idea built from a corrugated stainless wall, which lets it follow a flue that has an offset, a bend, or a slight jog in a way a rigid pipe can’t. That makes it a good fit for older Northeast Philadelphia houses where the flue wasn’t built straight. We install DuraFlex flexible liner systems because they’re engineered for that kind of routing and hold up to the heat and condensation the flue sees over time. A camera inspection tells us which flues can take a flexible liner and which need something else.
Liner Replacement
Liner replacement is when the existing liner has reached the end of its life and a new one is installed in its place. We replace liners that are cracked, corroded, or no longer matched to the appliance, and we pull the old liner where it can be removed cleanly. The camera tells us what’s coming out and what goes back in, and you see the same footage before we recommend anything.
Partial Rebuild
A partial rebuild repairs the damaged section of the chimney rather than taking down the whole structure, which is common when the problem is confined to the top courses of brick, the crown, or a section above the roofline. It’s often the sensible middle ground when the lower shaft is sound and only the exposed part has taken on water or freeze damage. We assess which sections can be repaired and which need replacement, then rebuild only what fails the test.
Full Chimney Rebuild
A full chimney rebuild is when the masonry has deteriorated past the point where spot repair holds, typically because years of water intrusion and freezing have broken down the brick and mortar through the entire stack. In that case we take the chimney down and rebuild it with proper flashing, a new crown, and a liner that matches the appliance. This is a substantial job, and we don’t recommend it unless the inspection shows the whole structure is compromised.
Liner Repair
Liner repair restores a flue that has cracks, gaps, or eroded joints but doesn’t need a full replacement. HeatShield resurfacing is the method we use here: it’s a repair system applied to the inside of the flue that seals those defects and restores the liner’s integrity, and we’re certified to apply it. It’s a strong option when the chimney structure is sound but the flue surface needs work.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Liner & Rebuild
We work with professional-grade products because the material inside your chimney is the whole reason the job lasts. DuraFlex flexible liner systems are what we install when a flue needs to follow a bend or offset, and we know where those systems are built to take stress and where the connections need attention. HeatShield is the resurfacing method we’re certified to apply, and it’s the right tool when a flue needs its integrity restored without a full liner going in.
We also source from Olympia Chimney and Copperfield, two of the most respected wholesale chimney supply networks in the trade, so the components that go into your chimney are specified for the job rather than pulled off a big-box shelf. Whether you have a DuraFlex system, a HeatShield-resurfaced flue, or any other make, we can help.
Signs You Need Chimney Liner & Rebuild Right Now
- Smoke rolling back into the room. If smoke comes back through the fireplace instead of going up the flue, the liner may be blocked, undersized, or broken at the joints. It’s a sign the flue isn’t doing its one job, and it usually gets worse, not better.
- Crumbling or flaking inside the flue. When the clay tiles break down or the mortar between them erodes, the flue loses the surface that keeps gases contained. That’s a liner problem, and the camera shows exactly where it is.
- Smoke smell in the house when the fireplace isn’t in use. A draft that pulls cold air and soot smells back down usually points to a liner that no longer seals. If you smell it on cold mornings, it’s worth a look before you light another fire.
- Water on the firebox floor or rusted damper. Water getting past a failed crown, cap, or flashing can reach the flue and the masonry behind it. Left alone, freeze-thaw cycles in Bustleton’s winters widen the damage and can push a repair toward a rebuild.
- Visible cracks in the brick above the roofline. When the exterior courses are cracked and spalling, the masonry itself is taking on water. A partial or full rebuild may be the honest answer, and we’ll tell you which from the inspection, not from the sales call.
Our Chimney Liner & Rebuild Process – Step by Step
- 1
Camera inspection of the full flue. We run a camera down the flue so we can see cracks, gaps, offsets, and blockages rather than guess at them. That footage is the basis for everything that follows, and you see it too.
- 2
A written recommendation and a flat-price estimate. We explain what the inspection found, which repair it points to, and why, then put the estimate in writing before any work is booked. If the chimney can safely wait, we say so.
- 3
Sizing and material selection. For a liner, we match the diameter and material to the appliance venting into the flue, then specify the product by name. That’s where the choice between stainless, flexible, or resurfacing gets made.
- 4
Installation or rebuild. We install the liner, apply the resurfacing, or rebuild the masonry as the job requires, with attention to insulation, flashing, and the crown. The work is done to the estimate, not around it.
- 5
Final camera pass and photo report. We run the camera again after the work so you can see the finished flue and keep the photos. A follow-up sweep the next season keeps the system verified.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Liner & Rebuild Cost in Bustleton?
A typical stainless or flexible liner installation in Bustleton runs roughly $2,400 to $6,500 depending on the flue height, the liner diameter, and whether insulation and new components go in with it. Liner repair with HeatShield resurfacing often falls in the $1,000 to $2,800 range. A partial rebuild typically runs $1,500 to $4,500, and a full chimney rebuild can run $9,000 to $20,000 or more when the whole stack comes down and goes back up with a new liner, crown, and flashing. These are estimates, and the written estimate sets the final price.
What moves the number: the height of the chimney, the condition of the masonry around it, whether the old liner can be pulled cleanly, and how much of the structure has water damage. You avoid overpaying by getting the camera footage first and a written scope second, so you’re not paying for work the chimney doesn’t need. The free estimate includes the inspection, the recommendation, and the flat price, and nothing is booked until you agree to it.
Chimney Liner & Rebuild Near Bustleton – Our Service Area
We work throughout Bustleton and the surrounding towns, including Northeast Philadelphia, Rhawnhurst, Penndel, Warminster, Village Shires, Elkins Park, Jenkintown, Willow Grove, Roslyn, Glenside, and Hatboro. Many of these visits can be scheduled the same day, and dispatch runs from 7am to 7pm, Sunday through Friday. Whether you need a liner or a chimney liner & rebuild, the process starts with the same camera inspection. For the full range of service, see Chimney Sweep Bustleton.
Serving Bustleton, PA – Our Local Coverage Area
We serve Bustleton and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Liner & Rebuild in Bustleton
Chimney liner and rebuild work covers two related repairs: installing or restoring the liner inside the flue, and rebuilding the masonry structure of the chimney itself. The liner is what carries smoke and gases up and out, and the rebuild addresses the brick, mortar, crown, and flashing around it. We do both, along with chimney liner & rebuild work in neighboring towns, so one call covers the whole system.
A liner installation usually takes a day, and resurfacing with HeatShield can take a day or two depending on cure time. A partial rebuild typically runs several days, and a full rebuild takes longer because the masonry has to come down, go back up, and cure. We give you the timeline in the written estimate so you can plan around it.
Liner installations typically run $2,400 to $6,500, HeatShield resurfacing around $1,000 to $2,800, partial rebuilds $1,500 to $4,500, and full rebuilds $9,000 to $20,000 or more. The written estimate sets the final price, and the inspection is free. Call (833) 350-7109 for an exact quote, and estimates are free.
Yes. We install DuraFlex flexible liner systems and we’re certified to apply HeatShield resurfacing, and we work with Olympia Chimney and Copperfield components. We can service those brands and others you may already have in your chimney. The right material gets specified by name once we’ve seen the flue on camera.
Same-day visits are often possible in Bustleton, and dispatch runs 7am to 7pm, Sunday through Friday. We’re closed on Saturday, and a call outside dispatch hours is booked into the next opening. Call (833) 350-7109, and we answer 24/7.
Warranty terms come from the manufacturer on the liner and resurfacing products and are spelled out with the estimate, so you know what’s covered before the work starts. We explain the terms for the specific product going into your flue. Ask for the details when you get the written estimate.
Clear the area around the fireplace hearth and give us a path to the roof access, since both liner and rebuild work start from the top of the chimney. Move anything fragile away from the work area, and note any appliance venting into the flue so we can match the liner to it. If you have prior inspection reports or photos, have them ready; they help us compare.
Schedule Your Chimney Liner & Rebuild Service in Bustleton Today
If the flue is cracked, the masonry is failing, or a sweep told you the liner needs work, we’ll inspect it with a camera and give you a written flat-price estimate before anything is booked. Call (833) 350-7109 for a no-obligation estimate. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday.
Written by the team at Chimney Sweep Bustleton.