Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Cap & Crown for Bustleton Homeowners
A missing or rusted-out cap is the reason water gets into a chimney that otherwise works fine. Once rain runs down the flue, it soaks the liner, works into the brick, and shows up months later as a stain on your ceiling or a flue tile cracked from a freeze. The cap and the crown are the two parts of the chimney that keep the weather out, and when either fails, everything below it pays the price. We handle the full system, not just the sweep, so you don’t need a second contractor for a job this specific. Our technicians have up to 9 years of experience, and we work on cap and crown problems across Bustleton and the surrounding neighborhoods. We install Gelco and Famco caps and use HeatShield for crown and liner work. Call (833) 350-7109 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm.
What Our Chimney Cap & Crown Service Includes
Six kinds of work fall under this service, and which one you need depends on what’s actually failing. A cap that’s missing, a crown that’s cracked, a flue that’s shifted out of line after settling. We look at it before we quote it.
Cap Installation
A cap is the lid over the flue, and installing one is the cheapest way to stop water and animals from getting into a chimney that doesn’t have one. You need a cap if the top of your flue is open to the sky, which is common on older homes in Bustleton where a cap was never put back after a repair. We measure the flue opening, fit a stainless or galvanized cap to the exact dimensions, and anchor it so it stays put through wind and snow load. We use purpose-engineered caps from Gelco and Famco rather than a generic hardware-store cover that rusts out in a few seasons.

Cap Replacement
A cap that’s rusted through, bent, or rattling loose is doing more harm than good, because a damaged cap can block airflow or let water pool on top of the flue. Replacement is the right call when the mesh is torn or the top has rusted past patching. We pull the old cap, check the flue tile and crown underneath for damage the failing cap may have caused, then fit a new cap sized to the flue. If the cap failed because the crown is cracked, we handle both in one visit.

Crown Repair
The crown is the concrete or mortar slab on top of the chimney that sheds water away from the brick. When it cracks, water runs into the masonry instead of off it, and that’s how a chimney starts to come apart from the top down. Small cracks we repair by patching; a crown that has broken apart gets rebuilt. We form it with a slight slope so water actually runs off, which is the detail a lot of crowns are missing.

Crown Coating
Crown coating is a protective layer applied over a crown that’s still sound but showing surface wear, and it buys years before a rebuild is needed. If the crown is intact but has hairline cracks and a rough surface, coating seals it against water. We use HeatShield resurfacing products for this, which restore the surface rather than just painting over the problem. Coating only works on a crown that’s structurally sound; if it has failed, we tell you and quote the repair instead.
Multi-Flue Cap
A multi-flue cap covers two or more flues in a single chimney with one top, which is common on larger homes and any chimney serving more than one appliance. You need one when separate single caps leave gaps where water and birds get in between the flues. We build the cap to span the full crown, with individual openings for each flue, so the whole top of the chimney is protected as one unit. This is a custom-fit job, not something a standard cap can do.
Custom Cap
A custom cap is made to fit a chimney that standard sizes won’t cover, whether that’s an oversize flue, an unusual shape, or a crown that requires a specific mounting. You need one when an off-the-shelf cap leaves gaps or sits crooked on the flue. We measure the actual opening and have the cap built to it, using Gelco or Famco components sized for the job, so the fit is right and the seal holds.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Cap & Crown
We work with professional-grade products because the difference shows up a few winters later, when a cheap cap has rusted through and a proper one hasn’t. Gelco and Famco caps are built specifically for chimney duty, with the mesh and structural work to handle wind and weather on a roof. We fit both, matched to your flue size and the way your chimney is constructed. DuraFlex flexible liner systems come into play when a failed crown has let water into the flue and the liner needs work at the same time. HeatShield is our choice for crown resurfacing and for restoring liner integrity without a full replacement.
We work with Olympia Chimney and Copperfield components as well, so the parts under a new cap or alongside a crown repair come from supply networks the trade actually uses. We aren’t tied to a single maker, and we won’t tell you one brand fits every chimney. The right material depends on your flue, your crown, and what failed first. Whether you have Gelco, Famco, or any other make on top, we can help. If you’re not sure what’s up there, that’s what the inspection is for.
Signs You Need Chimney Cap & Crown Right Now
- Water stains on the ceiling or chimney breast. A stain that shows up after heavy rain usually means water is getting past the crown or a missing cap and running down the outside of the flue. It won’t stop on its own, and each storm pushes more water into the masonry.
- Cracked or crumbling crown. If you can see cracks in the slab on top of the chimney, or chunks of mortar flaking off, the crown has stopped shedding water. Left alone, that water freezes in the brick and widens the damage.
- A missing or loose cap. A cap that’s gone, bent, or rattling lets rain straight into the flue and gives birds and squirrels an opening. A loose cap can also come off in a windstorm and land on the roof or the ground below.
- Rust streaks or a rusted cap top. Rust on the cap means it’s near the end of its life, and the rusted metal can drip onto the crown and stain the masonry. Replacing a rusted cap now is cheaper than repairing the flue it’s letting water into.
- Debris or animal nests in the flue. If you find leaves, twigs, or nesting material when you look down the flue, something got in through an open top. A proper cap closes that opening and keeps it closed.
Our Chimney Cap & Crown Process – Step by Step
- 1
We look at the whole top of the chimney. A cap and crown problem is rarely isolated, so we check the flue tile, the crown, the cap, and the brick at the top before recommending anything. If water has already reached the flue, we want to see that now, not after the cap goes on.
- 2
We show you what we found. Photos of the crown, the cap, and any cracks or water damage go into a written report, so you can see the problem yourself instead of taking our word for it. That’s how you know the quote matches the actual condition of your chimney.
- 3
We give you a written estimate with the options spelled out. Some crowns can be patched or coated; others need a rebuild. We lay out both where it applies, tell you what can safely wait, and set the price per job in writing before any work starts.
- 4
We do the work to fit the chimney. Caps are sized to the flue, crowns are formed with a proper slope so water runs off, and multi-flue and custom jobs are measured and built rather than guessed at. We use HeatShield for resurfacing and Gelco or Famco for caps where they fit the job.
- 5
We check the seal before we leave. The cap is anchored, the crown is checked for slope and coverage, and the flue is confirmed clear. You get the photos of the finished work, and a clear note on when the next sweep is due.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Bustleton?
What you’ll pay depends on which part failed and how far the damage has gone. A typical cap installation in Bustleton runs about $175 to $400 depending on the flue size and whether it’s a single or multi-flue cap. Cap replacement usually falls in the same range, plus a little more if the crown needs attention at the same time. Crown repair runs roughly $300 to $700 for patching and rebuilding a failed crown, and crown coating is on the lower end at around $200 to $450 because it’s a protective layer over a sound crown rather than a rebuild. A custom or multi-flue cap costs more than a standard single cap because it’s measured and built to the chimney. These are typical estimates for the area, not a fixed price; the written estimate sets the final number.
What affects the price: the size and shape of your flue, how much of the crown has failed, whether the chimney has more than one flue, and how much access the roof allows. A crown that’s cracked past patching costs more than one that only needs coating. To avoid overpaying, get the problem photographed and quoted in writing before work starts, and ask whether the crown can be coated instead of rebuilt. Our free estimate includes the inspection, the photos, and a written price per job, so you’re comparing the same scope if you get a second bid. Nothing gets recommended that the photos don’t support.
Chimney Cap & Crown Near Bustleton – Our Service Area
We work on caps and crowns across Bustleton and the nearby communities, including Penndel, Warminster, Village Shires, Elkins Park, Jenkintown, Willow Grove, Roslyn, Glenside, Hatboro, Northeast Philadelphia, and Rhawnhurst. Response times depend on the day and the job, but we book promptly and dispatch from 7am to 7pm, Sunday through Friday. If you’re just outside these areas, call and we’ll tell you whether we cover your address. For the full range of what we do, see our Chimney Sweep Bustleton page, and for cap and crown work in a neighboring town, our chimney cap & crown page covers Penndel.
Serving Bustleton, PA – Our Local Coverage Area
We serve Bustleton and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Cap & Crown in Bustleton
The cap is the covering over the top of the flue that keeps rain, animals, and debris out, while the crown is the concrete or mortar slab on top of the chimney that sheds water away from the brick. They’re two separate parts, but they fail together: a missing cap lets water hit the crown, and a cracked crown lets water into the masonry below. Together they’re the chimney’s first line of defense against weather. If either is damaged, the flue and liner are exposed. Call (833) 350-7109 for a free estimate on either.
Most cap installations and replacements take a couple of hours, and a crown repair or coating is usually a single visit, weather permitting. A full crown rebuild or a custom multi-flue cap takes longer because it has to be formed or built to fit and then set. We give you a realistic time frame in the written estimate so you know what to expect. Call (833) 350-7109 to book an inspection.
Caps typically run about $175 to $400, crown repair about $300 to $700, and crown coating about $200 to $450, depending on the flue size and how much has failed. A custom or multi-flue cap costs more because it’s measured and built rather than bought off the shelf. These are typical estimates, and the written estimate sets the final price after we’ve seen the chimney. Call (833) 350-7109 for an exact quote; estimates are free.
Yes. We install and service Gelco and Famco caps, and we work with Olympia Chimney and Copperfield components as well. We match the cap to your flue size and the way your chimney is built rather than forcing a standard size to fit. If your existing cap is a brand we haven’t listed, that’s fine, because the cap’s fit matters more than its label. Call and tell us what’s up there.
Same-day service is possible when the schedule allows, and we’ll tell you honestly when we can get out. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday; we’re closed Saturday. A call outside dispatch hours is booked into the next opening. Call (833) 350-7109 and we’ll find you a slot.
We stand behind the work we do, and the details of what’s covered are spelled out in your written estimate so there’s no guessing later. Caps we install are professional-grade Gelco and Famco units built for long-term performance, and crown work is done to shed water the way it should. If something isn’t right after the job, call us and we’ll look at it. Call (833) 350-7109 with any questions before you book.
You don’t need to do much: clear access to the fireplace or flue if we’ll be checking inside, and move anything breakable away from the hearth. If you’ve seen water stains or noticed a missing cap, tell us when you book so we bring the right materials. We handle the roof access and the rest. Call (833) 350-7109 to set it up. For cap and crown work in Warminster, see our chimney cap & crown page, and for more on our chimney cap & crown service, that page covers the full scope. You can also read about chimney repair, chimney liner & rebuild, and fireplace repair if the inspection turns up something beyond the cap and crown.
Schedule Your Chimney Cap & Crown Service in Bustleton Today
A cap or crown problem gets worse with every storm, so it’s worth looking at before the next one. Call (833) 350-7109 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. We’ll inspect the top of your chimney, show you the photos, and quote the work in writing with no obligation.
Written by the team at Chimney Sweep Bustleton.