Gas fireplace service
Sweep & inspection
Caps & crowns
Flue relining
Masonry repairLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Why Bustleton Homeowners Choose Gelco Chimney Cleaning
We provide independent Gelco chimney cleaning service in Bustleton, PA. That means we service and clean the Gelco cap, damper, or component already on your chimney, identify what’s actually failing, and fix it with parts that fit, without any manufacturer affiliation coloring the recommendation. We’re not a Gelco dealer and we’re not authorized by Gelco, so our advice follows the condition of your chimney, not a brand’s sales sheet.
Bustleton’s housing stock shapes this work. Most of the neighborhood is post-war brick rowhouses and twins from the late 1940s through the 1960s, almost all with one masonry fireplace and an exterior brick chimney that’s now 60 to 75 years old. Plenty of those chimneys have carried a Gelco cap for years, and plenty of them never got a modern liner. We see both on the same roof. Our technicians have up to 9 years of experience, and they’ve learned to look past the cap at the flue, the crown, and the firebox behind it.
Call (833) 350-7109 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Why Trust Chimney Sweep Bustleton for Your Gelco Chimney Cleaning?
Trust on a brand page comes from knowing the product, not from a logo on a website.
Our technicians read Gelco caps the way other crews read flue tiles. They know that a galvanized Gelco cap rusts through at the screen-to-frame seam rather than in the open field of the metal. They know a multi-flue cap with undersized screens will choke on creosote in a chimney that’s burned hot and often. They know a stainless cap set on legs that are too short sits close to the crown, traps debris, and speeds up spalling on the masonry below. Those details separate a real diagnosis from a shrug.
We service Gelco equipment with quality parts that fit it, sourced through professional supply networks like Olympia Chimney and Copperfield, and we choose OEM Gelco parts where exact fit and finish actually matter. Nothing we do requires cutting, drilling, or modifying the cap or damper frame in a way that would give a manufacturer a reason to deny a warranty claim. When a part has failed inside a reasonable window, the way we remove and reinstall it protects your position.
That’s the difference between a company that cleans a chimney and one that understands the cap bolted to the top of it. We’re an independent provider, not a Gelco representative, and we’re comfortable saying a Gelco product is the wrong choice for a particular flue when it is.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Common Gelco Chimney Cleaning Problems We Fix in Bustleton
These are the failures that come up most often on Gelco components around Bustleton, and what causes each one.
- Rust-through at the screen-to-frame seam on galvanized multi-flue caps. This is the classic galvanized failure, and it shows up after roughly 8 to 12 years of weather. Water sits at the joint where the screen meets the frame, and that’s where the metal goes first. Once the seam opens, rain blows in and animals find the gap. Bustleton’s freeze-thaw winters speed this up, because water trapped in the seam freezes, expands, and pries the joint open further each season.
- Clogged spark screens on Gelco multi-flue caps. Screens with tight mesh catch creosote and soot instead of letting them fall back down the flue. A clogged screen restricts draft and turns a fireplace that used to draw well into one that smokes into the room. It’s a cleaning problem with a screen-specification answer, not a masonry problem.
- Hardened damper gaskets on Gelco top-mount dampers. The gasket is what seals the damper when the fireplace is closed up and not in use. Heat cycling and humid summers harden it until it stops sealing. The result is heat loss up the chimney in winter and downdraft into the room when the fireplace sits idle, which reads to some homeowners as a drafty house rather than a damper issue.
- Inadequate leg height on stainless Gelco caps. A stainless cap can be in perfect condition and still cause trouble. Legs that are too short leave the cap sitting low over a masonry crown, trapping moisture and debris and accelerating crown spalling. Right product, wrong fit for the chimney.
- Undersized or missing screen panels after storm damage. A loose screen panel or a cap that’s lost hardware lets chimney swifts and squirrels in. The nest material adds a second fuel load inside the flue, and the screen damage goes unnoticed until a fall cleaning turns it up. Breeds like Bustleton’s chimney swifts take advantage of a missing cap quickly.
Every one of these traces back to a specific place on the product, which is why we look at the whole assembly before we quote anything.
Gelco Parts & Our Repair-vs-Replace Approach
OEM Gelco parts go in when exact fit and finish matter, and that usually means the frame is still sound. A replacement screen panel or a new damper gasket on an otherwise healthy cap is a repair worth doing. Full replacements are a different decision, and quality aftermarket stainless caps and dampers are often the better value there, because the new unit can be sized properly to your flue configuration rather than matched to a frame that’s already compromised.
We repair when the cap frame is intact and only the screen or gasket has failed. We recommend replacement when rust has reached the structural welds, or when the existing cap no longer matches the flue layout and no amount of patching will change that. We don’t carry a warehouse of parts and we don’t claim to stock genuine Gelco inventory. What we do is specify the right part by name for the job in front of us.
Call (833) 350-7109 for a free estimate and we’ll tell you which side of that line your cap sits on.
See the difference
Before
After
Before
After
Before
AfterOur Gelco Service Process – Step by Step
Our process runs the same way on every Gelco job, and each step exists because skipping it causes callbacks.
- 1
Diagnosis. We inspect the cap, the crown, the flue, and the damper together. A Gelco damper that won’t seal is often a symptom of a cap that isn’t venting the way it should, so we don’t treat them as separate problems.
- 2
Repair or install. If it’s a screen or gasket, we fit the replacement panel or OEM gasket to the existing frame. If it’s a full cap or damper replacement, we size the new unit to the flue, set the leg height so it clears the crown properly, and seal the perimeter.
- 3
Test. We verify draft and check that the damper seats with a clean seal, then sweep the flue if the screen clog or damper failure has left soot behind. Smoke shouldn’t roll into the room on a cold start when we leave.
- 4
Warranty position. We document what we removed, what we installed, and why, so there’s a clear record your Gelco warranty has something to stand on if the cap itself was still under coverage.
Same-day service is often possible when the schedule allows, and the cap or damper work itself usually takes under two hours on a straightforward job.
Gelco Products We Service & Install in Bustleton
We work on the full range of Gelco chimney products found on Bustleton homes. That includes Gelco Multi-Flue Caps in stainless and black galvanized, Gelco Single-Flue Caps with built-in spark screens, Gelco Top-Mount Dampers, and Gelco Custom Fabricated Caps sized to an unusual flue arrangement. We also handle the components around them: chimney caps and crowns, liner work, chimney repair and rebuilds, and fireplace repair, so a Gelco cap that’s fine but sits over a failing crown gets the whole assembly addressed in one visit rather than two contractors.
We Also Service These Brands
Gelco is one brand in a trade that uses many. We install DuraFlex flexible liner systems, we’re certified to apply HeatShield chimney resurfacing, and we source components from Olympia Chimney and Copperfield along with Famco caps. That range matters when the answer for your chimney isn’t Gelco, because we can say so and still do the work. One call covers the cap, the liner, the crown, and the firebox.
FAQs – Gelco Chimney Cleaning Service in Bustleton
No. We are an independent Gelco service provider and we have no manufacturer affiliation, dealership, or authorization from Gelco. We service Gelco equipment as an independent shop, which means our recommendations follow the condition of your chimney rather than a brand relationship.
You can usually replace just the screen if the cap frame is sound. A clogged or corroded screen panel on an otherwise solid frame is a straightforward swap with an OEM or exact-fit stainless panel. If the rust has reached the structural welds at the frame, a full replacement is the safer call. Call (833) 350-7109 for a free estimate and we’ll tell you which you’re looking at.
The gasket and the pivot hardware are the usual culprits. The gasket hardens from heat cycling and stops sealing, and the linkage can bind when soot builds up around it. In most cases a new damper gasket and a clean of the mechanism restores it, and the damper doesn’t need replacing. Call (833) 350-7109 to book an inspection.
A clogged spark screen is the most common cap-related cause of a smoky fireplace. When soot and creosote block the mesh, draft drops and smoke comes back into the room on start-up. A gritty black dust on the cap screen and smoke on cold starts together point to it. A pro can confirm it in one visit. Call (833) 350-7109 for a free estimate.
Upgrade to stainless if the rust has reached the frame welds or the seam has opened up. Galvanized caps rust through at that seam after 8 to 12 years, and patching a compromised weld rarely lasts. If the rust is surface-level only, a repair can still make sense. Call (833) 350-7109 and we’ll give you a straight answer.
Yes, we use OEM Gelco parts where exact fit and finish matter, such as replacement screen panels and damper gaskets. We don’t stock genuine Gelco inventory, but we specify the right part for the job. For full replacements, a quality aftermarket stainless cap is often a better value and we’ll tell you when that’s the case.
Most cap and damper work takes under two hours on a straightforward job, and a cleaning on top of it adds time depending on how much creosote has built up. We give you the estimate before we start. Call (833) 350-7109 for a free estimate.
Proper service with the right parts protects your warranty, and improper work is what puts it at risk. We install OEM Gelco parts where fit matters and we document what we did, so there’s a clear record if a claim ever comes up. We can’t speak for Gelco’s warranty terms directly, but we don’t install anything that would undermine your position. Call (833) 350-7109 with questions.
A standard chimney sweep in Bustleton typically runs $150 to $350, and cap or damper work is priced separately based on the part and the access. We give a written estimate before any work begins, and the price on that estimate is the price you pay. Call (833) 350-7109 for an exact quote, estimates are free.
We service and install Gelco Multi-Flue Caps, Single-Flue Caps with built-in spark screens, Top-Mount Dampers, and Custom Fabricated Caps. We also handle the surrounding system, so a cap replacement that uncovers a crown or liner problem gets addressed as part of the same job. Call (833) 350-7109 to book.
Written by the team at Chimney Sweep Bustleton.